ScreenBeam ECB6250K02 Network Adapter Starter Kit MoCA 2.5 - Faster | Ethernet Over Coax Network Adapter for Higher Speed Internet - MoCA Starter Kit for Streaming, Gaming, WFH - High Use Starter Kit (ECB6250K02) – High Use

Salida a tu país: 13-20 de Septiembre del 2026

Para comprar en web necesitás verificación en dos pasos activa. Te la pedimos una sola vez.

• M

  MT

  28 de diciembre de 2025

  Upgraded from Cable to Fiber and extended WiFi mesh network using Cable lines

  I recently upgraded from cable to fiber and was looking for a way to get better coverage from my mesh network. The master of my mesh had been set-up within a couple feet of my fiber modem/router to enable a physical connection of the two through an ethernet cable. Having two access points right next to each other limited my coverage. I bought a pair of MoCA Network Adapters and was able to move the mesh network master to the far end of my house and send the signal back to my fiber modem/router through my cable lines. This process was simple and took less than 20 minutes (mainly disconnecting and reconnecting the cables and hardware). It worked perfectly and I now have much better speeds/coverage throughout my entire home.Ver másVer menos

  1 persona la encontró útil

• D

  DennisGa

  If you have a poor WiFi signal you're dealing with. YOU NEED THIS SYSTEM!

  This MoCA 2.5 system is the bomb! My job is remote, and I work for a company in Massachusetts while living in Arizona. I work with CAD modeling software and the models get pretty big with 1000's of parts. Previously, I was using WiFi which was provided by COX and their modem with panoramic WiFi didn't cut it, download speeds were horrible. If I was near the router I would get 325-330 Mbps. In the room where my computer system is which is a straight run down a hallway, I was getting 10-20 Mbps. I installed a net extender and the best I could get with it was about 30-40 Mbps.It would take 30 minutes to upload the model I was working on and that would sometimes result in a communication error.After installing a ScreenBeam MoCA 2.5 which was so easy to install, I was downloading at 324.7 and that was through a secure VPN tunnel! Model open time was 33 seconds! These devices are amazing and will be saving me from lots of frustration and lost time! I will probably buy 2 more of these extenders for 2 more rooms.The only drawback I will say is the installation took 3 coax cables at the router and 1 in the room where it was going. The system I purchased only came with 2. Normally it wouldn't have been a big deal because over the years, I accumulated dozens of coax BUT, we moved in to our AZ home back in March and I threw out all the junk I didn't want to carry across the country and the coax cables were part of the cleanup. I got these the evening before Thanksgiving and I was fortunate enough to have my cousin stop by and bring me a coax cable and stay for Thanksgiving dinner. It was a 10 minute install and it works flawlessly! So make sure you have a spare coax cable or 2 hanging around.The image below is a picture of my laptop computer on the left and my desktop computer on the right. The left is running the MoCA 2.5 system and the right is using Cox WiFi at 2.5 GHZ with a net extender halfway between the modem and my desktop. Total length between modem and computer room is about 55-60 feet.Ver másVer menos

  4 personas la encontraron útil

• J

  Jorge

  30 de julio de 2026

  Great Ethernet over RG6 Coax cable adapter

  This product far exceeded my expectations. After wrestling for three days with a similar product from another company—only to discover that the Ethernet ports on one of the units were defective—I decided to try the ScreenBeam MoCA adapter. It worked flawlessly on the first attempt right out of the box, effortlessly bridging a 160-foot stretch of RG6 coaxial cable across my house (measured via a simple TDR technique). I am running a multi-gigabit cable connection, and this adapter cleanly delivers the full 1.45 Gbps of speed arriving from my modem with zero bottlenecking. One feature that truly differentiates it from competitors is its 5V DC power supply, compared to the 12V used by other brands. This lower voltage means each adapter dissipates very little heat and runs completely cool, whereas the competing product felt warm to the touch. You can confidently expect excellent reliability, a long lifespan, and low power consumption from this product.Ver másVer menos
• S

  supertech

  29 de noviembre de 2025

  It works great and simple to set up! Highly recommended.

  This worked great for me. It feels like a high-quality adapter, and I would highly recommend it if you need one. It’s very simple to set up once you figure out where your coax splitter is. It genuinely improved our home setup—I was sick of Roku buffering in the basement due to a Wi-Fi dead spot, and now everything runs at maximum speed.One note for FiOS users: if you’re using the FiOS G3100 router, remember that it has a built-in MoCA adapter. You’ll only need this adapter if you want to bring an Ethernet signal to another room. And if you want Ethernet in multiple rooms, you’ll need one adapter per room.Also, if you're planning to put a wireless access point in another room, keep in mind that the FiOS E3200 extender already has its own built-in MoCA adapter. In my case, I specifically needed Ethernet in additional rooms, which is why this adapter was essential.Ver másVer menos

  3 personas la encontraron útil

• K

  KC

  ECB6250 can be used from FIOS ONT to your Router

  4 STARS, the device works but the documentation on this is hard to come by with very general information on the admin pages. I'll try to cover what I can in this review.I recently upgraded my FIOS internet speed from 100Mbps to 200Mbps b/c it was the same price. Fun fact, FIOS provisions 300Mbps for the 200Mbps plan so I actually tripled my speeds at the same price.The FIOS ONT can only do 100Mbps through coax to their router. I can't run ethernet due to house scheme but coax is ran in each room already with a splitter in the basement. In comes MoCA and this ECB6250 device by Actionntec.The first photo you can see how I got the adapter to fit inside the FIOS box as well as the basic setup. You could likely use a plug splitter to save some more space as well as shorter cables but I just used what I had. It's a bit snug but it fits just fine.I used the app on my phone to chat to a rep and they noticed my ordered speed plan and switched my ONT from coax to ethernet. Easy.If you don't have FIOS TV or another MoCA device it's safe to say these will work out of the box and you hook em up exactly as I have. If however you do have FIOS TV you need to set these adapters to use D-band High and frequencies at 1400 and above. FIOS uses 1000MHz for MoCA on WAN and 1150MHz for MoCA on LAN. This is where I hit my first wall as the settings and information on what they do are basically non existent. I was trying to also use my old ECB2200V, long story short the ECB2200V is not compatible b/c you can't access its admin page. It scans higher bands and interferes with ECB6250 in a bad way.To access the admin page of these devices you'll need to power them and connect them directly to a computer via ethernet. If they are already daisy chained in succession then you can access both but only after you change their IP address. They all should come with the default static IP address of 192.168.144.200.Instructions to access GUI or admin page.Change your ethernet adapter settings IPv4IP Address 192.168.144.2Subnet Mask 255.255.255.0Gateway and DNS settings leave blankNow browse to 192.168.144.200Username is admin, password is actiontecNow you can browse to 192.168.144.200 to access the admin pageOn the Moca Settings page, to adjust so it only uses D-High and 3 channels which should give you 1.5Gps total throughput is set LOF to 1400 and uncheck the other bands. The key after that is to disable network search. If it's enabled it likely will try other bands then the one selected fails which will then cause crosstalk and you'll get interference and all sorts of issues. You need to do this to BOTH devices. I also set adapter names which is optional.The Device Settings page is where you can change the static IP address, I kept the one closer to the ONT default and changed the one at my router to 192.168.144.201.I uploaded the Status of them to show how it should look to avoid using lower frequencies and bands.Good luck!
• A

  Amazon Customer

  31 de julio de 2026

  Double the speed of wifi

  Easy to set up with a visual manual. My speeds went from 400-500 mbps to 900.